Pannier Hardware Decaleur Hack

With the first batch of Docena bags landing at their new owner’s this week, I wanted to share a bit about the hardware hack I have been rolling with for over a year now.  I opted to engineer a rock solid quick release system around commonly available pannier hooks.  They are cheaper, lighter, faster on/off and familiar to most cyclists outside of the french rando historical reenactment scene.  Likewise, I hacked a Nitto Lamp holder two with an old MTB handlebar and 10mm cabinet pull to male the handlebar side of the mount.  I wholly believe convenience and safety are key tenants as part of my quest to bring front loading bikes to the mainstream, getting there with familiar hardware can only help.  Here is a pic of the end hard mounted to the handlebars.

8.30 decaleur hack-1The next step is prepping your pannier hardware of choice.  I went with Ortlieb because the locking mechanism is simple and strong.  The mounting rail adds a bit of welcome rigidity to the bag, and there is little weight penalty with the molded plastic structure.  I mount the bare hooks on the 10mm “decaleur” rail to get them centered.

8.30 decaleur hack-2Put the bag on the rack and make sure the height of the mounting rail works out with the space between Docena rear pockets and the top flap.

8.30 decaleur hack-3This is a place where the adjustability of the Nitto mount hack really shines.  there are miltiple degrees of freedom in moving the mounting rail forward, back up and down by simply rotating around the two clamping axis.  With two rotating axis you end up wiht a reasonable amount of adjustment.  In the last few months the Nitto Lamp holder 2 has also shown up on our shores in a variety of mounting bracket lengths.  Once happy with how it all lines up, mark you horizontal line on the bag at the bottom of your bracket

8.30 decaleur hack-4Taking the bag over to the work bench, use a ruler to locate and align the center of the rail to the center of your bag.  This is the start of where you will want to be as careful as possible.  Measure twice  and be certain of every step.

8.30 decaleur hack-5From there I set the rail into position, and mark the mounting holes.

8.30 decaleur hack-6I use a hot soldering iron to make the holes and sear the material from fraying in a single pass.  I have also seen this done with a hot nail.  Use some common sense, do not burn your fingers being careless about the process.  This is best done with the stiffener fully inserted in the final position.  You will want the holes to pass all the way through and fully engage the bag and coroplast stiffener.

8.30 decaleur hack-7My picture of the mounting hardware turned out terrible.  I will insert one from the next bag I set up.  It really is the most straight forward step, just nuts and bolts.  That is it.  From there the nylon strap goes over the tombstone on your lower rack, and the pannier hooks grab your hacked decaleur just like the panniers most of us are familiar with.  If I know I will be leaving the bag on, or riding for long periods off pavement, I take the time run the bottom velcro straps through the rack.  Honestly though, I do not use them for most of my day to day riding.

8.30 decaleur hack-8Based of feedback from other riders using Swift bags the Berthoud decaleur for threadless stems is also a good solution.  There are a variety of off the shelf solutions that will get you where you want to go.  My hack above works better than most IMO, shaves a bit of $$ and feeds your inner maker monkey.  At some point we will offer a packaged solution, but there are a few other projects ahead of it in line.

 

5 thoughts on “Pannier Hardware Decaleur Hack”

  1. Awesome set up! The first time I remember “meeting” you was on the Touring board of Bike Forums in a thread about decaleurs. It must five years ago or more now. This was the first and only time I’ve seen someone use the Nitto lamp holder hack. It’s brilliant. Great post!

  2. I was wondering about doing something like this! Thomson X2 threadless and no spacers leads to a limit to how to attach a rando bag via a quick-release mechanism. I also think I like this more than a regular decaleur, seems much more secure but also quicker and easier. Thanks for sharing these little tips you have!

Leave a Reply

Your email address will not be published. Required fields are marked *